At 10,000 pieces, HASAMASE is listed at $9.70 per unit, but a buyer still chooses the plate set and market version before ordering. A 3-in-1 sandwich maker is a hinged appliance with interchangeable sandwich, waffle, and grill/panini plates; this catalogue-based sourcing assessment examines GTITSM-1 at 850W.
// 01 — Key takeaways
Use At Home was founded in 2005. Its Trust Center documents a 15,000 m² factory, seven production lines, and a minimum 12-month warranty.
The GTITSM-1 record lists tube heating, 220V, and 50/60Hz operation.
Interchangeable grill/panini, waffle, and sandwich-toaster plates share one unit.
The typical MOQ is 100 units; published price tiers begin at 1,000 pieces.
Lowest published unit price at 10,000 pieces; the listed ladder starts at $10.50 for 1,000 pieces.
Figures come from the live HASAMASE catalogue, directly fetched sibling records, and the Use At Home Trust Center.
// 02 — Product fit
What should buyers look for in a 3-in-1 sandwich maker?
Review the plate formats, electrical version, coating care, latch action, cleaning route, and price tier as one order. HASAMASE combines three interchangeable plate types with 850W input. A menu trial then shows whether the supplied plates suit the buyer’s bread, filling, and service pattern.
Does 850W decide the cooking result?
No. 850W is rated electrical input, not a cooking-time promise. Plate geometry, contact, controller cycling, food load, and starting temperature also affect the result. Use wattage for circuit and model planning. For performance, record warm-up, plate-temperature spread, browning, release, and cycle time with the same recipe, ambient conditions, sensors, and starting temperature. Report watts as electrical input in sales copy; report a cooking claim only with its food load, endpoint, and recorded time.
Do three plate sets match the target menu?
The record names grill/panini, waffle, and sandwich-toaster plates. Map each retail claim to one supplied plate, then put the included set, replacement-part code, finish, and locking method on the order.
What does the 8-slice field mean for a batch?
The catalogue places “8” in a field called “number of slices,” but it does not say whether eight means bread slices loaded, sealed pockets, or finished pieces. Those counts can differ. If one closed plate makes four sealed pockets from eight bread slices, say that plainly; do not convert one count into another. Load the intended bread dimensions and filling mass, photograph the open and closed plate, and count all three ways. Put the observed term, bread size, and loading pattern on the package and purchase order.
“We answer fast, we honour our specifications, and we treat your first order as the start of a partnership, not a one-off transaction.”
— Mi Lan, Founder, Guilin Use at Home Technology Co., Ltd.
// 03 — Specifications
Which 3-in-1 sandwich maker specs decide the order?
Order-critical fields are model GTITSM-1, 850W tube heating, 220V at 50/60Hz, three aluminum non-stick plate formats, two indicator lights, and a 26×15×25cm package at 1.8kg. The signed specification must assign the catalogue’s ABS and Bakelite labels to the correct housing parts.
HASAMASE / GTITSM-1 spec sheet
Rev. 2026.08
Treat the table as catalogue input. The signed order sets the market version and assigns each housing material.
| Spec | Catalogue value | Why it matters |
|---|---|---|
| ERP SKU / model | HASAMASE / GTITSM-1 | Keeps the quote, artwork, trial record, and production file on one identity. |
| Rated power | 850W | Defines the electrical input named on labels and test documents. |
| Heating method | Heating tube method | Sets the heating platform for control and warm-up evaluation. |
| Voltage / frequency | 220V / 50–60Hz | Must align with the destination cord, plug, label, and conformity route. |
| Plate formats | Grill/panini, waffle, sandwich toaster | Defines the three included menu functions and spare-part set. |
| Plate material / finish | Aluminum / non-stick surface | Drives food-contact documentation, release testing, and cleaning instructions. |
| Housing fields | “Material: ABS” and “Body Material: Bakelite” | Both appear in the source record, so the order must identify which part uses each material. |
| Indicators | Power light + food-ready light | The trial should document when each light changes during control cycling. |
| Capacity field | 8 slices | Copy the defined bread size, loading pattern, and count term into the purchase order. |
| Package | 26×15×25cm / 1.8kg | Provides the one-unit packing input; no master-carton data was supplied. |
| Configuration | Electric; app control: no; private mould: no | Prevents software or exclusive-tooling assumptions. |
| Warranty / customization | 1 year / OEM & ODM available | Connects after-sales terms to the branded order. |
Why do the two housing-material fields matter?
The record lists both ABS and Bakelite without assigning them to parts. The bill of materials and food-zone drawing should identify each component so incoming inspection and retail copy describe the same construction.
Can 220V serve every listed plug market?
No. The catalogue lists 220V alongside US, UK, EU, and AU plug options, but a plug option does not create a universal electrical version. For each destination, put voltage, frequency, plug, cord, label language, and the required conformity route in the quote and order. Give each market version its own model suffix or configuration code. Do not carry a plug icon onto a 220V label unless that voltage-and-plug combination is the documented order version.
// 04 — Comparison
How does HASAMASE compare with three fetched models?
Directly fetched records place HASAMASE between 800W and 1000W models and above a 600W model. The table compares each plate set and its lowest published tier. Because those tiers use different quantities, compare the deposit due at the buyer’s chosen volume.
| Model | Power | Published plate record | Lowest fetched price |
|---|---|---|---|
| HASAMASE Featured | 850W | Grill/panini, waffle, sandwich toaster | $9.70 at 10,000 |
| UAHW45 | 600W | Waffle, sandwich, egg puff, taiyaki | $10.00 at 5,000 |
| UAHW84 | 800W | Sandwich and waffle maker; accessory field lists cable | $10.00 at 5,000 |
| UAH-20802 | 1000W | Grill/panini, waffle, sandwich toaster | $6.80 at 5,000 |
Each sibling was fetched by SKU. Its “lowest” price is its own bottom published tier, not a matched order quantity.
Why is the lowest price not the whole comparison?
Compare the actual order quantity: UAH-20802 is $6.80 at 5,000 pieces, while HASAMASE is $9.70 at 10,000. Add the plate set, package, market version, warranty terms, and deposit due before choosing.
// 05 — Acceptance
What should an importer test before issuing the PO?
Run all three plate sets with the destination voltage, planned bread and filling, fixed recipe, cleaning method, and final label version. Record plate fit, latch action, warm-up, temperature spread, indicator cycles, release, housing temperature, and post-cleaning condition. Put the accepted limits and photos in the order file.
Evidence boundary: No authenticated HASAMASE test record was supplied for warm-up time, plate-temperature spread, coating cycles, release force, or food throughput under stated conditions. This assessment therefore makes no model-specific numerical performance claim. The protocol below shows how the buyer can create that record.
Do the plates lock, release, and sit flat?
Fit and remove each cold plate. Record rocking, gaps, edge alignment, latch position, and tool use; repeat after cooking and cooldown. Keep the accepted unit as the reference for clips, hinge travel, and spare-part interchange.
Does heat reach both cooking zones evenly?
Place calibrated sensors on a fixed grid. Log ambient temperature, warm-up, and controller cycles; then compare upper and lower plates under one food load. Set the allowable spread for the recipe and retain the sensor IDs, method, and raw readings.
- Record SKU HASAMASE, model GTITSM-1, voltage, frequency, plug, cord, and plate inventory.
- Inspect each aluminum non-stick surface under consistent light before cooking.
- Fit all plate sets and document latch, hinge, gap, and release behavior.
- Map warm-up and control cycling with calibrated sensors and a stated method.
- Run the intended sandwich, waffle, and grill menu with fixed inputs.
- Cool and clean the plates with the intended nonscratching tools, then inspect the finish.
- Attach accepted photos, readings, artwork, packing, and warranty terms to the order file.
// 06 — Standards
Which safety and food-contact references matter?
Use the destination’s appliance-safety and food-contact rules. IEC 60335-2-9 gives the relevant household-and-similar scope for grills, toasters, and waffle irons. The FDA Food Code provides a foodservice reference for durable, smooth, cleanable food-contact surfaces and non-scratching care of certain coatings.
Where does IEC 60335-2-9 apply?
IEC 60335-2-9:2019 covers household and similar portable cooking appliances up to 250V, including contact grills, toasters, and waffle irons. Its scope excludes professional food-processing and commercial-catering appliances. This public scope page does not identify a HASAMASE certificate.
What does the FDA Food Code add?
The FDA Food Code 2022 is a model for retail and foodservice rules. Chapter 4 describes durable, corrosion-resistant, nonabsorbent, smooth, easily cleanable food-contact surfaces and non-scratching tools for certain non-stick coatings. Use the rule adopted at the destination.
// 07 — Sourcing
What do MOQ, price tiers, and B2B fit mean?
The typical MOQ is 100 units, while published prices begin at 1,000. The record lists 15–30 days for bulk production after deposit, 3–7 days for trial units, 30/70 T/T, and FOB China, EXW, or CIF.
Which buyers fit the 850W three-plate format?
Distributors can use one chassis for sandwich, waffle, and grill lines. Hotel buyers must state the venue and duty pattern. Private-label teams can put logo, packaging, color, and product details in the GTITSM-1 OEM or ODM brief.
How does the published HASAMASE price ladder work?
Published tiers fall from $10.50 at 1,000 pieces to $9.70 at 10,000.
| Quantity | Published price per unit | Published discount |
|---|---|---|
| 1,000 | $10.50 | $0.00 |
| 2,000 | $10.20 | $0.30 |
| 5,000 | $10.00 | $0.50 |
| 10,000 | $9.70 | $0.80 |
Can a buyer order 100 units at $10.50?
No. The catalogue states a typical 100-unit MOQ, but the price table begins at 1,000. Request a current 100-unit quote instead of copying the $10.50 tier into the budget.
Which terms belong on the quotation?
Put the model, market version, quantity, unit price, Incoterm and named place, 30/70 payment triggers, timing, plate inventory, package, artwork, destination documents, and warranty contact on the quotation. Alibaba Trade Assurance is supported.
Request the current tier through the Use At Home quote form; name HASAMASE, GTITSM-1, destination, quantity, and plate set.
// 08 — Manufacturing
How we manufacture and document HASAMASE
Factory documents should connect tooling identity, the heating circuit, plate-fit control, destination documents, and the 12-month warranty to the buyer’s signed order. HASAMASE is marked “private mould: no,” so the file must identify the actual housing, plates, materials, tests, and artwork.
Tooling, molding, and incoming parts
Use At Home has in-house tooling and molding capability; HASAMASE is listed as private mould: no. The order file identifies the housing, aluminum plates, clips, latch, hinge, heating tube, cord, color, and artwork used for that buyer.
Heating tube and control-circuit burn-in
The order’s control plan states the burn-in method, load, duration, sampling level, and limits for the 850W heating tube, wiring, indicators, protective parts, and switching behavior.
Plate-fit and electrical quality control
Line inspection covers plate seating, interchange, hinge travel, latch closure, conductor routing, indicators, and finish. Packing inspection covers the three plate formats, model label, market cord, manual, artwork, and unit pack.
Certifications and 12-month warranty
The Trust Center names CE and RoHS among factory capabilities. The order lists only the marks and reports that apply to HASAMASE and its destination. The branded manual and carton state the 12-month warranty route.
// 09 — Buyer questions
What do buyers ask about a 3-in-1 sandwich maker?
Buyers ask whether three functions justify one chassis, whether removable plates help cleaning, what the commercial terms cover, and whether a household-and-similar appliance suits catering. These answers separate catalogue facts from decisions tied to the buyer’s menu, venue, and destination.
Is a 3-in-1 sandwich maker worth it?
A 3-in-1 sandwich maker is worthwhile when the planned menu will use sandwich, waffle, and grill or panini plates and one accepted chassis is easier to stock than three appliances. HASAMASE provides those three formats. The buyer still needs matched recipes, plate identification, cleaning instructions, and replacement-part support.
Are removable sandwich-maker plates easier to clean?
Removable plates can make food-contact surfaces easier to access away from the electrical body, but clip geometry, coating care, seams, and the permitted cleaning method still matter. HASAMASE lists interchangeable aluminum plates with a non-stick surface. Use nonscratching utensils and cleaning aids that match the coating declaration and instructions.
What are the MOQ, lead time, and warranty for HASAMASE?
The record states a typical MOQ of 100 units, bulk production in 15–30 days after deposit, trial units in 3–7 days, and a 12-month warranty. Published price tiers start at 1,000 pieces, so the typical MOQ is not a $10.50 price offer. FOB China, EXW, and CIF are available.
Can HASAMASE be specified for commercial catering?
The catalogue includes commercial and hotel use tags, but intended use must match the destination’s rules and evidence. IEC 60335-2-9 covers household and similar portable cooking appliances while excluding professional commercial catering. State the actual venue, operator, duty cycle, and conformity route before describing the final configuration as catering equipment.
// 10 — Decision
Conclusion: should HASAMASE enter the product line?
Shortlist HASAMASE when the line needs 850W input, three interchangeable plate formats, four published price tiers, and OEM or ODM support. Before ordering, put the market version, housing-material map, plate inventory, and acceptance limits in the signed specification.
Compare the menu and order quantity. HASAMASE lists more input power than UAHW45; UAHW45 names a fourth mold; UAH-20802 reaches a lower tier at 5,000 pieces. Choose the model whose plate set and deposit fit the planned line.
Featured product
HASAMASE 3-in-1 sandwich maker
GTITSM-1 · 850W · grill/panini, waffle, and sandwich plates · 220V · 50/60Hz
From $9.70/unit at 10,000 pieces
Reference HASAMASE, destination, quantity, plate inventory, and private-label brief in the quote.
Similar products
Ready to order or need a wholesale quote?
Use At Home manufactures these appliances direct from our Guilin, China factory — OEM, private-label and B2B welcome. Tell us your market and volume.
