28W Cordless Floor Scrubber: Essential B2B Buyer Guide
At 1,000 units, UAH20XX is listed at $77 each—$8 below its 200-unit tier, or an $8,000 difference across the order. A cordless floor scrubber is a battery-powered hard-floor washer that applies clean water, lifts debris, and separates recovered liquid; this guide tests UAH20XX against route, tank, compliance, and wholesale needs.
// 01 — Key takeaways
Key takeaways for a wholesale decision
UAH20XX prioritizes a larger three-part tank system, a 60-minute catalog runtime, and flat-body reach. Its 28W drive, 2600mAh battery, 100–240V input, and four verified quantity tiers give buyers enough hard data to compare samples, plan a route test, and calculate the correct order tier.
Founded in 2005, Use At Home operates a 15,000 m² facility with seven production lines. Review the documented factory facts in the Use At Home Trust Center.
Rated power for the UAH20XX sweep, mop, and wash platform.
Catalog runtime per charge from a 2600mAh battery; charging time is three hours.
Clean-water tank, paired with a 350ml dirty-water tank and 150ml trash compartment.
Listed product weight, with a 31 × 21.1 × 115.7cm assembled size.
// 02 — Buyer checks
What should B2B buyers check before ordering a cordless floor scrubber?
Buyers should match the scrubber to the real floor route, verify how tanks are emptied and rinsed, and test water recovery on every intended surface. Runtime alone does not prove cleaning coverage. A sample trial should record route duration, refill points, remaining charge, edge access, operator handling, and the floor’s final condition.
Match the machine to the route, not a room label
A 60-minute runtime is useful only when the route can be completed within that operating window. Map corridors, furniture clearances, thresholds, elevators, storage, and the walk back to the charging point. The UAH20XX can lie flat, but the catalog does not state a minimum clearance height, so test the actual furniture gap with a sample.
Tank size can set the practical limit before the battery does. The clean tank holds 750ml, while the dirty-water tank holds 350ml. A route trial should show which tank needs attention first under the buyer’s own water-flow setting and soil level.
Check recovery, separation, and daily cleanup
The product record lists automatic spraying, automatic cleaning, and solid-liquid separation. It also gives debris its own 150ml trash compartment. These are clear design features, but they do not eliminate operator care. Ask the sample team to time emptying, rinse the dirty tank, inspect the brush, and check whether any debris remains around seals or channels.
Wet-floor control is a purchasing issue, not just a housekeeping detail. The U.S. Occupational Safety and Health Administration identifies wet floors and spills as slip, trip, and fall hazards. A buyer should therefore document water recovery and signage procedures during the sample test instead of assuming that one pass always leaves every floor ready for traffic.
Use a product-specific sample acceptance checklist
Set the pass limits before the sample arrives, then preserve the route map, floor type, liquid, operator, charger, and result with the report. This keeps catalog values separate from buyer-owned acceptance decisions.
| Test | How to test UAH20XX | Write the pass rule before testing |
|---|---|---|
| Route duration | Time the mapped route from first cleaning pass through return to storage; log turns, repeat passes, and all stops separately. | Buyer-set maximum total time and maximum active-cleaning time. |
| Dirty-tank interruption | Mark whether the 350ml recovery tank requires emptying before the route ends and record the interruption point. | Buyer-set maximum number and duration of planned emptying stops. |
| Residual water | Inspect straight runs, turns, edges, and stop points under working light immediately after the pass; photograph trails or pooling. | No condition outside the buyer’s written water-recovery limit on each approved floor. |
| Flat-body clearance | Measure the lowest required furniture gap, then run the head and body through it at the working angle without contact, leakage, or loss of the cleaning path. | Passes the buyer’s measured minimum gap throughout the required reach. |
| Charge time | After the agreed discharge point, charge with the supplied charger and record elapsed time to the machine’s full-charge indication. | Observed time meets the signed specification and the buyer’s shift schedule. |
| Remaining battery | Record the machine’s battery indication at route end. If it gives no percentage, continue on a fixed test lane and record reserve minutes. | Buyer-set minimum indication or reserve time after the complete route. |
// 03 — Specifications
What do the UAH20XX cordless floor scrubber specifications mean in practice?
The UAH20XX is a 28W cordless wet-and-dry floor washer with a 2600mAh battery and separate clean, dirty, and solid-debris containers. Its strongest procurement case is the combination of 60-minute listed runtime, a 750ml clean tank, flat-body use, and globally adaptable 100–240V electrical input.
UAH20XX spec sheet
Rev. 2026.08
| Spec | This model | Why it matters |
|---|---|---|
| Material | ABS | Defines the listed body material for sample and order checks. |
| Rated power | 28W | Identifies the electrical configuration being quoted. |
| Voltage | 100–240V | Supports market planning, subject to the correct plug and documentation. |
| Battery | 2600mAh | Should match the sample label and approved specification sheet. |
| Charge and runtime | 3 hours / 60 minutes | Sets the baseline for route and charging tests. |
| Water and debris system | 750ml clean / 350ml dirty / 150ml trash | Separates fresh water, recovered liquid, and solid debris. |
| Product size | 31 × 21.1 × 115.7cm | Guides storage, display, and assembled-product checks. |
| Product weight | 4.5kg | Informs handling trials and product specification control. |
| Listed functions and reach | Sweep, mop, and wash; automatic spraying and cleaning; solid-liquid separation; flat-body operation | Defines the functions and access claims that require confirmation on the approved sample. |
| Export carton | 80 × 24 × 34.8cm; 1 unit; 6.9kg | Provides the catalog carton data for freight planning. |
Tank architecture matters more than one headline capacity
A “750ml tank” headline describes only the clean-water side. Procurement documents should retain all three values: 750ml clean water, 350ml dirty water, and 150ml solid debris. Keeping them separate prevents an incomplete comparison with products that publish only their largest tank.
Do not turn tank volume into a promised square-meter figure. Water use changes with flow, passes, soil, and floor condition. Measure refill and emptying points during the actual route test.
Packaging data belongs in the landed-cost file
The UAH20XX export carton is listed at 80 × 24 × 34.8cm, one unit per carton, and 6.9kg. Use those values as catalog inputs, then confirm final packing on the pro forma invoice. Any OEM carton, accessory, or insert change may require a revised packing specification.
// 04 — Comparison
How does UAH20XX compare with two 25W models?
This cordless floor scrubber costs more at its opening tier but carries the largest clean-water capacity in this three-model comparison. UAH21X and UAH22X both use 25W, 2600mAh platforms with 460ml clean and 235ml dirty tanks. The right choice depends on tank plan, product weight, charge time, and target price.
Verified catalog comparison
| Model | Power | Tank system | Charge / runtime | Product weight | Catalog price |
|---|---|---|---|---|---|
| UAH20XX Featured | 28W | 750ml clean / 350ml dirty / 150ml trash | 3h / 60min | 4.5kg | $85 |
| UAH22X | 25W | 460ml clean / 235ml dirty / 175ml trash | 3–4h / 60min | 2.7kg | $52 |
| UAH21X | 25W | 460ml clean / 235ml dirty / 175ml trash | 4–5h / 60min | 2.6kg | $46 |
Read price as a configuration decision
The table uses each model’s fetched catalog record, not a market estimate. UAH20XX adds a 28W configuration and larger listed tanks, while the two 25W models are lighter and enter at lower catalog prices. These facts identify different starting points; they do not prove which unit performs better on a buyer’s floor.
Request side-by-side samples when the program volume justifies it. Run the same debris mix, route, operator, and cleanup procedure. Record pass count and residual water without converting observations into unsupported laboratory claims.
// 05 — Route planning
Will a 60-minute runtime fit the cleaning route?
A 60-minute cordless floor scrubber runtime can fit a compact route, but it is not a coverage guarantee. Buyers should subtract setup, turns, repeated passes, tank care, and the return to storage from the available window. Test the route on an aged sample battery and define the minimum acceptable remaining charge.
Calculate a route with observed time
Start a stopwatch when the operator begins active cleaning and record every stop. Repeat the route on more than one day if soil loads vary. The useful result is not a theoretical area figure; it is a route record showing whether the machine completes the required work with a practical reserve.
Use the catalog runtime in the main spec sheet only as the test ceiling. Because no cleaning-width or square-meter productivity figure is supplied, calculate no theoretical coverage figure; use the timed route record.
Plan around both liquid tanks
The dirty-water tank is smaller than the clean-water tank. That relationship may make recovery-tank emptying the first interruption, depending on spray flow and pickup. Observe both levels during the trial. Define who empties the tank, where it is emptied, and how the parts dry before storage.
Turn the charge test into a shift decision
Use the observed charge result from the acceptance checklist to decide whether one machine can cover the planned shift pattern or whether the program needs another unit or a different charging window. Confirm the local plug, rating label, and charging instructions before approving packaging.
// 06 — Use cases
Can a floor scrubber clean every type of floor?
No cordless floor scrubber should be approved for every floor by default. The UAH20XX record describes hard-surface wet and dry cleaning, but it does not list every finish. Buyers should obtain the flooring maker’s care instructions, test an inconspicuous area, use an approved cleaner, and reject any result that changes the surface.
What does wet and dry mean here?
In this product category, wet and dry describes one workflow that handles loose debris, applies water, washes the hard floor, and collects recovered liquid. It does not mean the machine is suitable for every carpet, unfinished wood surface, chemical spill, or industrial pickup task.
Can it be used under furniture?
The catalog lists operation with the body tilted flat. That feature is relevant to beds, cabinets, and low furniture, but no minimum clearance is published. Measure the customer’s actual clearance and confirm that the head, body, and handle can move through the required angle without contact.
Which buyers are a practical fit?
Distributors, hotel-supply programs, residential-appliance brands, and private-label sellers may value the three-in-one sweep, mop, and wash format. Fit still depends on the approved hard-floor list, storage, operator routine, and after-sales plan. A hospitality buyer should also document wet-floor controls around guests and staff.
// 07 — Safety
How should buyers check safety and cleaning chemistry?
For a cordless floor scrubber, check electrical scope, destination-market documents, cleaner labels, and residual-water control as separate workstreams. A model name or voltage range is not a complete compliance file. The order specification should state the target country, plug, label language, required marks, approved cleaning solution, and the buyer’s sample acceptance procedure.
Which electrical standard covers household wet scrubbers?
IEC 60335-2-10:2021 addresses the safety of household and similar electric floor treatment and wet scrubbing machines rated up to 250V, including battery-operated appliances. The standard’s scope is relevant to this category, but relevance does not itself certify UAH20XX. Request documents for the exact configuration and destination.
Which cleaning solution should a buyer specify?
Use only a solution approved for the machine and floor. The U.S. Environmental Protection Agency Safer Choice product search lists certified cleaning products, including floor-care options. That resource can support purchasing research, but the buyer must still follow the machine manual, chemical label, and flooring instructions.
How should residual-water risk be tested?
Run the machine over the intended surface with the approved liquid, then inspect the entire path under working light. Record trails, turns, edges, and stops. Define warning-sign and access-control rules for any wet area. This turns OSHA’s general wet-floor warning into an observable local procedure.
“The right floor scrubber is the one that finishes the buyer’s real route, leaves an acceptable surface, and can be cleaned correctly after every shift.”
— Mi Lan, Founder, Guilin Use at Home Technology Co., LTD
// 08 — Quality control
Recommended buyer QC plan for a UAH20XX order
The steps below are buyer-recommended controls, not a description of undocumented factory procedures. Put them in the purchase specification, agree who performs each check, and require evidence for the inspected production lot before release.
Freeze the approved sample and specification
Attach dated sample photos and the signed spec sheet to the order. Define color, logo placement, rating label, plug, manual language, carton artwork, accessories, and objective cosmetic limits so an inspector has one controlled reference.
Define lot sampling and identity checks
State the inspection stage, sampling method, defect classes, and acceptance limits in the purchase documents. For every sampled unit, match the model and rating labels, battery and charger identifiers, tank configuration, plug, accessories, and packaging to the approved file.
Repeat functional acceptance tests
On the agreed sample size, check assembly, charging, spray delivery, brush operation, liquid recovery, tank fit, leaks, flat-body travel, controls, and shutdown behavior. Re-run the approved-floor residual-water test and record failures by serial or carton identifier.
Release only against documentary evidence
Before shipment, require the inspection report, packing list, production-lot photos, approved artwork, and destination-market documents that the buyer’s compliance adviser has identified for the exact configuration. Do not infer certification, warranty coverage, or test completion from a catalog label alone.
// 09 — Wholesale
How do wholesale, OEM, and private-label terms work?
The current catalog ladder has four quantity tiers; the table below is the controlling price reference for this guide. OEM work can cover logo, packaging, color, and agreed specifications. Quote requests should identify the market, forecast volume, plug, label language, packaging changes, and required compliance documents.
Use the published price ladder accurately
| Quantity | Catalog discount | Catalog unit price |
|---|---|---|
| 200 units | $0.00 | $85.00 |
| 500 units | $2.00 | $83.00 |
| 700 units | $2.00 | $83.00 |
| 1,000 units | $8.00 | $77.00 |
These are real catalog tiers for UAH20XX, not a freight-inclusive estimate. Confirm the live quotation, packing, Incoterm, tooling, samples, and any destination-specific costs before calculating landed cost.
Confirm lead time, payment, and shipping on the quotation
The supplier record gives a typical 15–30-day bulk production window after deposit and a 3–7-day sample window. Standard terms are 30% deposit and 70% before shipment by T/T, with Alibaba Trade Assurance supported. FOB, EXW, and CIF arrangements are available; the live quotation controls the order.
The current UAH20XX product record states that every unit carries a 12-month warranty. Confirm covered defects, exclusions, claim routing, the coverage start date, and the available remedy in the signed quotation and warranty terms; the product record does not define those details.
Lock the private-label specification before production
OEM and ODM options include logo, packaging, color, and agreed specification changes. Treat every change as controlled data. Approve the sample, artwork, color reference, plug, rating label, manual language, carton marks, accessory list, and warranty channel in writing.
Guilin Use at Home Technology Co., LTD manufactures across its stated niche of vacuum food sealers and kitchen appliances as well as selected floor-care products. Buyers can request a live UAH20XX quotation with their market and volume.
// 10 — FAQ
Cordless floor scrubber frequently asked questions
These answers address the questions buyers most often need before sampling: category definition, floor compatibility, runtime, pricing, and compliance. They distinguish catalog facts from tests that must happen on the buyer’s own route and flooring, which prevents a sales headline from becoming an unsupported acceptance promise.
Is a cordless floor scrubber the same as a wet and dry vacuum?
Can UAH20XX be used on every hard floor?
How long does the UAH20XX battery run and charge?
What are the UAH20XX order tiers and prices?
What compliance information should a buyer request?
// 11 — Decision
Final cordless floor scrubber buying decision
Choose UAH20XX only when its approved sample completes the mapped route, fits the lowest required clearance, meets the water-recovery limit, and retains the buyer’s required battery reserve. Choose a sibling model when the side-by-side trial and landed-cost file better fit the brief.
The decisive next step is a written sample plan, not another feature list. Put floor types, route timing, tank care, residual-water inspection, plug, labeling, packaging, and commercial terms on one approval sheet. Then compare the observed result with the real catalog specification.
Featured model
UAH20XX Floor Scrubber
28W · 2600mAh · 750ml clean tank · 60-minute runtime
From $85/unit at 200 units
Similar products
Lavadora de Pisos Sem Fio, 25W, 3 em 1 Úmido e Seco
Ready to order or need a wholesale quote?
Use At Home manufactures these appliances direct from our Guilin, China factory — OEM, private-label and B2B welcome. Tell us your market and volume.
